A: Yes, the Easy Glide^™ comes unassembled in one box. You will also need a Phillips-head screwdriver which is not provided. As long as you properly follow the instruction manual it should take approximately 20-30 minutes to install.

Watch our Easy Glide^™ Sit-Stand work platform assembly video for more details.

A: It can hold 10.5 kg total (8 kg monitor, 2.5kg keyboard tray).

A: Yes, the Easy Glide^™ attaches to the back of a desk via an adjustable clamp. The clamp works on desk depths 7.6mm to 50mm.

A: The Easy Glide^™ has a maximum reach of 762mm; however, the Easy Glide^™ can be used on desks as shallow as 533.4mm.

A: Under normal use, the platform is stable. If you want to maximize the durability of the product, please do not lean or apply excessive force to the keyboard platform. If the platform seems unstable during normal use, adjust the monitor arm tension (see below for location and instructions).

A: This is located on the upper part of the dynamic arm (part A), it appears zoomed in in Step 9 of the manual.

Watch our Easy Glide^™ Sit-Stand work platform tensioning video for more details.

A: Please refer again to Step 9 in the manual. There is a tension adjustment bolt on the top of the dynamic arm. You will need the 8mm socket and 6mm allen key provided (alternatively you can use a socket wrench if preferred – not provided). Turn clockwise for heavier weights and counter clockwise for lighter weights.

Watch our Easy Glide^™ Sit-Stand work platform tensioning video for more details.

A: This adjustment is shown in step 13 of the manual. On top of the lower arm is an adjustment that requires a 5mm allen key. Turn clockwise until your monitor stays at your preferred height. Note – don’t confuse this adjustment with the monitor tilt adjustment behind the VESA plate.

Watch our Easy Glide^™ Sit-Stand work platform tensioning video for more details.

A: Behind the VESA plate is an adjustment that requires a 2.5mm allen key. Turn clockwise for heavier weights and counter clockwise for lighter weights until you are able to properly tilt your monitors. Please refer to step 12 of the manual.

Watch our Easy Glide^™ Sit-Stand work platform tensioning video for more details.

A: There are multiple ways to install the mounting plate (clamp) onto the base. For thinner desks, use the most upper sets of holes, for thicker desks use the lower sets of holes. Per the manual, max desk thickness is 50.8mm and min desk thickness is 7.6mm.

A: Please refer to step 11 of the manual. You will first need to remove the cable cover from the dynamic arm. Then, route your cables along the arm and reinstall the cable cover on top of them.

Watch our Easy Glide^™ Sit-Stand work platform cable management video for more details.

A: Yes, please refer to step 10 of the manual. There is an adjustment at the bottom of the dynamic arm. This will require a 6mm allen key. Turn clockwise for heavier weights and counter clockwise for lighter weights.

Watch our Easy Glide^™ Sit-Stand work platform tensioning video for more details.

A: Yes, we have spare parts for purchase that we can supply. Contact our customer services team on 00800 1810 1810 whom will be happy to help.

A: 2 years.

Please refer to the Easy Glide™ product manual for full terms and conditions.

A: Yes, the Extend^™ comes unassembled in one box and includes hardware. You will also need a Phillips-head screwdriver which is not provided. As long as you properly follow the instruction manual it should take approximately 20-30 minutes to install.

A: The Extend^™ can hold 13.6 kg total (11.3 kg monitor, 2.2 kg keyboard tray).

A: Yes, the Extend^™ attaches to the back of a desk via an adjustable clamp. The clamp works on desk depths 15.8mm to 69.8mm.

A: The Extend^™ has a maximum reach of 1,016mm (1,056.5mm including the clamp); however, the Extend^™ can be used on desks as shallow as 584.2mm.

A: The Extend^™ Dual can accommodate monitors up to 609mm (24”) in width. Extend^™ single has no dimensional restrictions, only weight (11.3kg).

A: In order to place the M8 dynamic arm into the base you will need to remove the 180° stop screw located in the base. Please refer to step 3 in the manual, as you will need to remove the cable cover to access the screw.

A: Please refer to step 7 in the instruction manual. You will need to remove the 180° stop screw located at the top of the M8 arm.

A: Please follow the step 14 in the manual to adjust it flush to the desk, in order to find the angle adjustment bolt please remove the lower arm cover.

A: Please note that the monitor attachment plate has a direction on it indicating “top”, if not placed that way – there will be no option for quick release. If installed correctly, simply press the quick release tab and pull up on the monitor.

A: Yes, Extend^™ offers 180° of rotation so you can easily move the Sit-Stand out of the way if needed.

A: Yes there are 3 different height settings your monitor can be at. Remove your monitors from the crossbar (dual) or monitor mount (single). Unscrew the crossbar (dual) or monitor mount (single) from the upper arm. If you’d like your monitor(s) to be lower, reinsert the crossbar or monitor mount into a lower set of screw holes on the upper arm.

A: Under normal use, the keyboard platform is stable. If you want to maximize the durability of the product, please do not lean or apply excessive force to the keyboard platform. If the keyboard platform seems unstable, you will need to adjust the monitor arm tension (see below).

A: Please refer to step 12 of the manual, the tension adjustment bolt is located in part E (M8 Dynamic Arm) under a high gloss cover.

Watch our Extend^™ Sit-Stand work platform tensioning video for more details.

A: Yes, we have spare parts for purchase that we can supply. Please contact our customer services team on 00800 1810 1810 whom will be happy to help.

A: Yes, please refer to steps 15 and 16 in the manual. You will start by removing the cable cover from the lower arm. Route your keyboard and mouse cables through the lower arm and down into the channel on the M8 arm. Route your monitor cables through the M8 arm. Next, remove the cable cover from the rear of the base and guide all cables through. Reinsert both cable covers (lower arm and base).

Watch our Extend^™ Sit-Stand work platform cable management video for more details.

A: 5 years. Please see the product manual for full terms and conditions